Solid Surface Materials
06625-2
2.01 MATERIALS
A. Acceptable products:
1. One Source Group; Sultra
B. Characteristics
1. Material: Filled Blended Acrylic Sheet
2. Thickness; slab: ½" or ¼"
3. Colors: Indicated on Interior Finish Schedule.
4. Flame Spread, fuel contribution, and smoke development:
ASTM E84-95, Class A.
a. Flame Spread: <25.
b. Smoke Developed: <400.
5. Approvals: NSF Approved
GREENGUARD Approved
C. Accessory Products:
1. Adhesives: OSI SF 450 (Ohio Sealants Inc.)
2. Sealant: Manufacturer's recommended type.
3. Joint compound: Color matched, field applied
2.02 MANUFACTURED UNITS
A. Shower Floor
1. Product standard of quality: One Source Group Inc; Shower Base.
2. Characteristics:
a. Material: One Source Group Inc; Sultra
b. Configurations: Indicated Drawings; complete with standard cutouts for plumbing drain; ADA compliant where indicated.
c. Color: Indicated on Interior Finish Schedule.
B. Vanity Tops:
1. Product standard of quality: One Source Group Inc; Vanity Top
2. Characteristics:
a. Material: One Source Group Inc; Sultra
b. Configurations: Indicated on Drawings; complete with standard cutouts for plumbing brass.
c. Furnish products standard of quality manufacturer's standard underhung white china bowl.
d. Bowl Apron: 7½" by ¼" thickness by top length with tissue cutout.
e. Color: Indicated on Interior Finish Schedule.
C. Shower/Tub Surrounds:
1. Product standard of quality: One Source Group Inc; Option 1, four piece system and Option 2, three piece system.
2. Characteristics:
a. Material: One Source Group Inc; Sultra.
b. Panels: ¼" thickness flat panels; widths and heights indicated; complete with trim pieces.
c. Flame Spread, fuel contribution, and smoke development: ASTME84-95, Class A.
1) Flame Spread: <25
2) Smoke Developed: <400
d. Approvals: NSF Approved
GREENGUARD Approved
e. Color: Indicated on Interior Finish Schedule.
3. Accessories: Two surface applied soap dishes for each assembly; furnish loose for application at Project site.
2.03 FABRICATION
A. Shop assembly:
1. Employ product standard of quality manufacturer's authorized fabricator for solid surfacing material fabrication.
2. Factory cut and fabricate solid surfacing material to greatest extent possible to sizes and shapes indicated on reviewed shop drawings.
3. Lay-up selected colors to indicated configurations for edge treatments; prepare for final contouring.
4. Contour edges to indicated profile.
5. Furnish tops with cutouts for underhung bowls; match bowl profile. Insert undermount bowl mounting hardware into top underside during fabrication process for bowl installation in another Section.
6. Indicated height of backsplashes and endsplashes where indicated.
7. Bowl aprons: Provide separate for field installation; fabricate using concealed connections.
8. Exposed surfaces free from marks and blemishes; completely hide through material joints.
B. Tolerances:
1. Variation in size: ± 1/16"
2. Location of openings: ± 1/16" center to center.
PART 3-EXECUTION
3.01 INSTALLATION
A. Solid surfacing materials, general:
1. Install plumb, level and rigid, neatly scribed to adjoining surfaces where indicated in accord with manufacturer's installation instructions and reviewed shop drawings.
2. Adhere splashes to countertops and adjacent surfaces with specified adhesive.
3. Bowl skirts: attach using concealed fastener system after bowl and plumbing are installed.
4. Allow only factory finished surfaces to be exposed in finshed work.
5. Install wall panel shower/tub surrounds in accord with manufacturer's installation instructions to meet classification specified. Surface apply soap dishes where indicated or required, two per unit.
6. Removal of code compliance labels until final cleaning and code official verification of unit performance is prohibited; early label removal or installation of non-labeled units may be cause for rejection.
B. Sealant: Caulk perimeter of joints using above specified sealant; install in accord with Joint Sealants Section.
C. Clean installed units not more than 48 hours prior to Date of Substantial Completion. Repair or replace damaged or stained work.
